Unicall 0.0.5 & spandsp 0.0.4 with Asterisk 1.4.9 « Asterisk Unicall…

Unicall 0.0.5 & spandsp 0.0.4 with Asterisk 1.4.9 « Asterisk Unicall…

Si deseas soporte pagado por la configuracion de Unicall u OpenR2 contactame a moises.silva en el correo de google.

y cuando trato de sacar llamada me sale:
voip*CLI>
— Executing [95101652@L-DDN-DDI-CEL:1] Dial(“SIP/100-c0001240″, “Unicall/g1/5101652″) in new stack
MFC/R2 UniCall/1 Call control(1)
MFC/R2 UniCall/1 Make call
MFC/R2 UniCall/1 Creating a new call with CRN 32769
MFC/R2 UniCall/1 0001 -> [1/DIALING /Seize /Idle ]
— Called g1/5101652
[Mar 5 13:10:31] NOTICE[5371]: chan_unicall.c:2518 handle_uc_event: Unicall/1 event Dialing
[Mar 5 13:10:31] NOTICE[5371]: chan_unicall.c:1914 unicall_exception: Exception on 25, channel 1
MFC/R2 UniCall/1 [2/DIALING /Group I /DNIS ]
MFC/R2 UniCall/1 [2/DIALING /Group I /DNIS ]
MFC/R2 UniCall/1 [2/DIALING /Group I /DNIS ]
MFC/R2 UniCall/1 [2/DIALING /Group I /DNIS ]
MFC/R2 UniCall/1 [2/DIALING /Group I /DNIS ]
MFC/R2 UniCall/1 [2/DIALING /Group I /DNIS ]
MFC/R2 UniCall/1 [1/IDLE /Idle /Idle ]
[Mar 5 13:10:31] NOTICE[5371]: chan_unicall.c:2518 handle_uc_event: Unicall/1 event Protocol failure
[Mar 5 13:10:31] ERROR[5371]: chan_unicall.c:2522 handle_uc_event: Unicall/1 protocol error. Cause 32772
MFC/R2 UniCall/1 Channel echo cancel
MFC/R2 UniCall/1 Channel gains
MFC/R2 UniCall/1 Channel switching
— Hungup ‘UniCall/1-1′
== Everyone is busy/congested at this time (1:0/0/1)
— Executing [95101652@L-DDN-DDI-CEL:2] Hangup(“SIP/100-c0001240″, “”) in new stack
== Spawn extension (L-DDN-DDI-CEL, 95101652, 2) exited non-zero on ‘SIP/100-c0001240′
MFC/R2 UniCall/1 [1/IDLE /Idle /Idle ]
voip*CLI>

que sera?

Mi configuracion

zaptel.conf

# Span 1: WCT1/0 “Wildcard TE122 Card 0″ (MASTER)
span=1,1,0,cas,hdb3
# termtype: te
cas=1-15:1101
#dchan=16
cas=17-31:1101
# Span 2: WCTDM/0 “Wildcard AEX410 Board 1″
fxsks=32
fxsks=33
fxsks=34
fxsks=35
# Global data
loadzone = us
defaultzone = us

unicall.conf

[channels]
language=es
usecallerid=yes
hidecallerid=no
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
echotraining=yes
rxgain=0.0
txgain=0.0
group=1
callgroup=1
pickupgroup=1
immediate=no
musiconhold=default
protocolclass=mfcr2
; protocolvariant=co-land,30,1,16
protocolvariant=co-land,30,7,16
protocolend=cpe
group = 1
loglevel = 255
context= from-pstn
channel => 1-15
channel => 17-31
;skip time slot 16

extensions.conf

[from-pstn]
exten=>_.,1,Answer()
exten=>_.,n,Goto(ivr,s,1)
exten=>_.,n,Hangup

exten=>9260,1,Answer()
exten=>9260,n,Goto(ivr,s,1)
exten=>9260,n,Hangup

Tengo entendido q en el zapata.conf no se coloca nada del E1 pero aca les mando:

[trunkgroups]
[channels]
language=es
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
relaxdtmf=yes
rxgain=0.0
txgain=0.0
callgroup=1
pickupgroup=1
immediate=no
faxdetect=incoming
busydetect=yes
busycount=4

; Span 1: WCT1/0 “Wildcard TE122 Card 0″ (MASTER)
;group=1
;context=from-pstn
;switchtype = euroisdn
;signalling = pri_cpe
;channel => 1-31
; Span 2: WCTDM/0 “Wildcard AEX410 Board 1″
;;; line=”32 WCTDM/0/0 RED”
signalling=fxs_ks
callerid=asreceived
group=2
context=from-pstn
channel => 32
;;; line=”33 WCTDM/0/1 RED”
signalling=fxs_ks
callerid=asreceived
group=2
context=from-pstn
channel => 33
;;; line=”34 WCTDM/0/2 RED”
signalling=fxs_ks
callerid=asreceived
group=2
context=from-pstn
channel => 34
;;; line=”35 WCTDM/0/3 RED”
signalling=fxs_ks
callerid=asreceived
group=2
context=from-pstn
channel => 35

CLI> load chan_unicall.so

Asterisk 1.4

CLI> module load chan_unicall.so

Can you help me in this case ?
How can i load chan_unicall.so module ?
according to above post …. maybe you install MFC/R2 successful.

thanks amjt !

Thanks for reply.
But how can i load chan_unicall.so module ?
(What is command or edit any files?)

Regards!

I eventually will post a guide in the blog, but cannot give you a date for that.

I had install driver for my E1 Card … OK !
I tried to install astunicall 1.4.9-0.1 packages. But I can’t success (I tried install follow guide at http://www.soft-switch.org/unicall/installing-mfcr2.html).
I don’t know why , I don’t see anything such as : UC show channels,status,… in ‘Asterisk CLI>’ … Can you give me the reason about this ?
Can you show me how to install unicall for MFC/R2 step by step…:) if you can.

Thanks a lot !

BestRegards